BDM Probe Adapters Full Set For Kess Ktag KTM Trasdata BDM Probe Set 22pcs For Denso, Marelli, Bosch, Siemens
OBD2Tuner.com How To use BDM Probe Set For Kess Ktag KTM Trasdata BDM Probe Adapters Full Set:
1. Open the ECU
at least one part of the casing (top or bottom) needs to be removed
refer to other sources (Internet) to get information on which part needs removing on your
ECU
2. Locate the ECU BDM connector
usually a set of 10 – 12 pads in two rows (depending on the ECU)
pads may be 2.54 mm or 1.27 mm apart (depending on the ECU)
rows may be 2.54 mm or 5.08 mm apart (depending on the ECU)
if the ECU BDM connector can not be located, chances are that the BDM pads are scattered
all over the ECU PCB in which case you can not use the adapter directly – nevertheless it is
possible to manually route the adapter BDM signals to the ECU BDM pads (only for
advanced users)
3. Locate the ECU BDM pin 1 position
pin 1 is usually not clearly marked on the ECU BDM pin out
on an ECU with the standard Motorola BDM pin out pins 3 and 5 are connected to ground –
this can be checked either visually or using a multimeter tool
refer to other sources (Internet) to get more information on the pin 1 position for your ECU
4. Place the desired adapter in the frame saddle
make sure the pogo pins are facing out
lift the saddle so that the ECU can be slided under the frame adapter saddle
5. Place the ECU on the frame
inspect the adapter for pogo pin 1 location which is clearly marked
rotate the ECU on the frame so that the adapter pogo pin 1 and ECU BDM pin 1 match
make sure ECU is firmly sitting on the frame
double check the ECU position
6. Connect the multiplexer board and adapter
at this point multiplexer board should be connected to the adapter via MUX connector
this will allow LEDs on the adapter to illuminate the area of interest (where the pogo pins
need to touch the ECU BDM pads)
do not connect the tool yet
7. Connect the external power (+12 V) to the multiplexer
multiplexer external power is used to power the LEDs on the adapter allowing easier
positioning of the adapter pogo pins on the ECU BDM pads
red LED on multiplexer board will light up when external power (+12 V) is present
at this point the white LEDs on the adapter should also light up
do not connect the tool yet
8. Fine tune the ECU position
lower the frame adapter saddle to almost touch the ECU BDM pads
each adapter pogo pin needs to sit on a separate ECU BDM pad
if pogo pins do not sit on the pads you may be using the wrong adapter – do not use the
adapter in this case!
9. Lower the frame adapter saddle
each adapter pogo pin should sit on one ECU BDM pad
minimum down force should be applied when making the interconnection between the
adapter and ECU
10. Double check the adapter pogo pin and ECU BDM pad interconnection
in order not to damage the ECU and/or tool make sure that the steps above have been
performed correctly
11. Connect the tool to the multiplexer board
only connect one tool at any given moment to the multiplexer
make sure to use the correct 10-pin IDC connector (FGTECH, XPROG, BDM100&KTAG)
for interfacing the tool used:
○ use provided 10-pin to 10-pin cable with FGTECH or BDM100 tools
○ use provided 10-pin to 16-pin cable with XPROG tool
○ use manufacturer 10-pin to 25-pin cable with KTAG tool
do not connect the tool to the 10-pin IDC connector labeled MUX
do not power up the tool yet
12. For Bosch adapter only
Bosch ECUs need to have ECU power supplied on the pogo pins (2 and 9)
some tools provide dedicated ECU power (BDM100, KTAG) while others do not
(XPROG, FGTECH)
Bosch adapter can be used in both cases, providing that the jumper is properly placed on
the 3-pin header (found on the adapter)
place the jumper on the adapter on the 3-pin header to the correct position:
○ place jumper over left and central pins when using XPROG and FGTECH tools – this will use +12 V power delivered from the multiplexer board (external power) for powering the ECU
○ place jumper over right and central pins when using BDM100 or KTAG tools – this will use
+12 V power delivered by the tool for powering the ECU
13. For Siemens, Delphi and Marelli adapters only
Siemens, Delphi and Marelli do not provide ECU power on the pogo pins
in order to power the ECU +12 V and ground signals needs to be connected to the ECU separately (usually over the ECU interfacing connector)
in this case ECU power can be taken from multiplexer board connectors J2 (+12 V) and J3 (ground), otherwise provide the +12 V ECU power from additional source
refer to other sources (Internet) to get more information on the location of the +12 V and
ground pin location for your ECU
14. Connect the tool to the PC (or power up the tool)
perform software installation as described by the tool manufacturer if not done already
at this point the multiplexer, adapter and the ECU should be properly interconnected with
BDM signals and power lines
○ multiplexer red LED should be lit up
○ adapter white LEDs should be lit up
○ ECU power (+12 V) should be present
connect the tool to the PC (usually done over USB or serial connection)
15. Perform BDM operation(s)
start up the software package to operate the tool
perform desired BDM operation(s)Note: The user manual is used for reference; in fact, it depends. Try on your own risk.
Any need for BDM adapter full set BDM probe Denso, Marelli, Bosch, Siemens BDM Probe Adapters for KTAG KESS KTM Dimsport, just contact obd2tuner.com freely.
For More details information, welcome to Add my Whatsapp (+86 15889512468) or Skype obd2tuner.com) if you have, Your Private Secretary in Car Repair Area! 16 Hours Online at your Service!
www.OBD2Tuner.com- China OBD2 Tuner Tool Automotive Diagnostic Tools Car Key Programmer OBD2 ECU chip tuning tool Center.
Contacts:
Website: www.obd2tuner.com
Skype: OBD2Tuner.com
Email: info@obd2tuner.com
What;s app: +86 15889512468
没有评论:
发表评论